Members Only
Artikel
The Elektor DSP radio (1)
DSP world receiver with USB interface
Log hier in als abonnee om het artikel te lezen.
Dit Elektor-artikel verder lezen?
Probeer een digitaal lidmaatschap (Green) voor 6 maanden voor slechts € 6,33 per maand.
- Onbeperkt toegang tot Member Only artikelen
- 3 nieuwe edities van Elektor Magazine (digitaal)
- Meer dan 5000 Gerber-bestanden
- 20% ledenkorting op e-books (op elektor.nl)
- 10% ledenkorting op producten (op elektor.nl)
Probeer 6 maanden
Stopt automatisch.
Stopt automatisch.
Gerber bestand
De PCB bij dit artikel is als Gerber file beschikbaar gesteld. Elektor Members kunnen exclusief deze files gratis downloaden en gebruiken om de PCB zelf af te drukken met geschikte apparatuur óf de Gerber te laten drukken via een dienstverlener.
Elektor kan u bijvoorbeeld de PCB Service van onze partner Eurocircuits van harte aanbevelen of AISLER.
Het gebruik van onze Gerber files is vrijgegeven onder een Creative Commons- licentie. Creative Commons biedt auteurs, wetenschappers en andere creatieve makers de vrijheid om op een flexibele manier met hun auteursrechten om te gaan.
PCB
Extra info / Update
Features
- no set-up adjustments required
- Si4735 DSP receiver IC
- ATmega168 microcontroller
- USB interface using FT232R
- backlit 2 x 16 LCD panel
- battery voltage 4.8 to 6 V
- current consumption approximately 50 mA
- 3.3 V internal power supply
- power from PC over USB interface
- stereo audio output
- stereo audio amplifier (2 x LM386)
- RDS display
- AM from 153 kHz to 21.85 MHz
- automatic station search
- antenna signal strength indication in dBµV
- signal strength meter connection
- diode switching of AM band
- automatic tuning of AM resonant circuit
- switchable AM bandwidth
- optional PC control over USB
- tuning using rotary encoder
- four control pushbuttons
- station memory (30 AM presets and 30 FM presets)
- open-source firmware (free download)
- in-system programming interface
- printed circuit board available ready-populated and tested
- no set-up adjustments required
- Si4735 DSP receiver IC
- ATmega168 microcontroller
- USB interface using FT232R
- backlit 2 x 16 LCD panel
- battery voltage 4.8 to 6 V
- current consumption approximately 50 mA
- 3.3 V internal power supply
- power from PC over USB interface
- stereo audio output
- stereo audio amplifier (2 x LM386)
- RDS display
- AM from 153 kHz to 21.85 MHz
- automatic station search
- antenna signal strength indication in dBµV
- signal strength meter connection
- diode switching of AM band
- automatic tuning of AM resonant circuit
- switchable AM bandwidth
- optional PC control over USB
- tuning using rotary encoder
- four control pushbuttons
- station memory (30 AM presets and 30 FM presets)
- open-source firmware (free download)
- in-system programming interface
- printed circuit board available ready-populated and tested
Componenten
De BOM (Bill of Materials) lijst van Elektor is de meeste complete lijst met benodigdheden voor alle Elektor Labs projecten. Deze lijst is completer dan wat we kunnen publiceren in ons magazine en is geupdate met alle nieuwste componenten. Als lezer kunt u deze lijst hier downloaden.
Meer weten over onze BOM lijst? Lees het BOM lijst artikel voor alle informatie.
Onderdelenlijst
Resistors
(5%, 0.25 W)
R1-R3 = 100Ohm
R4,R5 = 470Ohm
R6-R8 = 22kOhm
R9,R10 = 1kOhm
R11 = 47Ohm
R12,R13 = 10Ohm
P1 = 10kOhm trimpot, linear, vertical adjustment, PCB mount, ALPS type RK09K11310KB (Farnell # 1191725)
Capacitors
C1,C23,C24,C26,C27 = 1uF 16V, electrolytic, radial, 5mm diameter
C2, C3 = 4.7uF 16V, electrolytic, radial, 5mm diameter
C4-C16 = 100nF, ceramic capacitor, 2.54 mm lead pitch
C17, C18 = 47pF, ceramic capacitor, NP0, 5.08mm lead pitch
C19, C20 = 22pF, ceramic capacitor, NP0, 5.08mm lead pitch
C21, C22 = 12pF, ceramic capacitor, NP0, 5.08mm lead pitch
C25 = 100uF 16V, electrolytic, radial, 6.3mm diameter
C28, C29 = 47uF 16 V, electrolytic, radial, 6.3mm diameter
C30, C31 = 470uF 16 V, electrolytic, radial, 8.0mm diameter
C32, C33 = 100nF, polyester (MKT), 5.08 mm lead pitch
Inductors
L1 = 10uH (Fine Inductors Fastron type SMCC-100X-YY)
L2 = 0.1uH (Fine Inductors Fastron type SMCC-R10X-YY)
L3 = 4.7uH (Fine Inductors Fastron type SMCC-4R7X-YY)
L4 = 220uH (Fine Inductors Fastron type SMCC-221X-YY)
L5 = 2.2mH (Fine Inductors Fastron type SMCC-222X-YY)
Semiconductors
D1-D5 = BAT48, Schottky diode, 330 mW, DO-35
D6,D7 = 1N4148
IC1 = LP2950ACZ-3.3/NOPB, LDO voltage regulator, 3.3 V, 100 mA, TO-92
IC2 = FT232RL, USB to serial UART interface, FTDI, SSOP-28
IC3 = ATmega168PA-PU, PDIP-28, programmed, Elektor # 100126-41)
IC4, IC5 = LM386N-1, DIL-8
Y1 = Si4735 broadcast AM/FM/SW/LW radio receiver carrier board, DIL-20, Elektor # 090740-71
Miscellaneous
ENC1 = Rotary encoder, vertical, 12 ppr, ALPS type EC12E1220401 (Farnell # 1520809)
JP1 = 3-way pinheader, 2.54 mm lead pitch + jumper
JP2-JP5 = 2-way pinheader, 2.54 mm lead pitch + jumper
K1-K3 = 2-way, screw-type terminal block, 5mm lead pitch
K4 = BNC connector 50 ohms, black, PCB, mount, Tyco Electronics type 1-1634612-0 (right angle);
type 1-1634505-0 (vertical) (Farnell # 1020957; # 1020960)
K5 = 3-way PCB terminal block, 5mm lead pitch
K6 = jack socket, 3.5mm, stereo (Farnell # 1267400)
K7 = USB socket type B, PCB mount
K8 = 6-way (2x3) header, wire-to-board (Farnell # 1096984)
LCD1 = Alphanumeric LCD 2x16, (Electronic Assembly type EA DOGM162W-A) + LED blue backlight (type EA LED55X31-B)
S1 = slide switch, SPDT, C&K type OS102011MS2QN1 (Farnell # 1201430)
S2-S5 = Tactile switch, SPNO, MULTIMEC type 3FTL6 (Farnell # 1132885) + elevation caps
X1 = 8MHz quartz crystal, low-profile, case type HC49
X2 = 32.768 kHz quartz crystal, cylindrical case (3x8 mm)
2 pcs IC socket, DIL-8
1 pc IC socket, DIL-28 narrow body
Sockets for LCD elevation
PCB, bare, Elektor # 100126-1
PCB ready assembled and tested, Elektor # 100126-91
(5%, 0.25 W)
R1-R3 = 100Ohm
R4,R5 = 470Ohm
R6-R8 = 22kOhm
R9,R10 = 1kOhm
R11 = 47Ohm
R12,R13 = 10Ohm
P1 = 10kOhm trimpot, linear, vertical adjustment, PCB mount, ALPS type RK09K11310KB (Farnell # 1191725)
Capacitors
C1,C23,C24,C26,C27 = 1uF 16V, electrolytic, radial, 5mm diameter
C2, C3 = 4.7uF 16V, electrolytic, radial, 5mm diameter
C4-C16 = 100nF, ceramic capacitor, 2.54 mm lead pitch
C17, C18 = 47pF, ceramic capacitor, NP0, 5.08mm lead pitch
C19, C20 = 22pF, ceramic capacitor, NP0, 5.08mm lead pitch
C21, C22 = 12pF, ceramic capacitor, NP0, 5.08mm lead pitch
C25 = 100uF 16V, electrolytic, radial, 6.3mm diameter
C28, C29 = 47uF 16 V, electrolytic, radial, 6.3mm diameter
C30, C31 = 470uF 16 V, electrolytic, radial, 8.0mm diameter
C32, C33 = 100nF, polyester (MKT), 5.08 mm lead pitch
Inductors
L1 = 10uH (Fine Inductors Fastron type SMCC-100X-YY)
L2 = 0.1uH (Fine Inductors Fastron type SMCC-R10X-YY)
L3 = 4.7uH (Fine Inductors Fastron type SMCC-4R7X-YY)
L4 = 220uH (Fine Inductors Fastron type SMCC-221X-YY)
L5 = 2.2mH (Fine Inductors Fastron type SMCC-222X-YY)
Semiconductors
D1-D5 = BAT48, Schottky diode, 330 mW, DO-35
D6,D7 = 1N4148
IC1 = LP2950ACZ-3.3/NOPB, LDO voltage regulator, 3.3 V, 100 mA, TO-92
IC2 = FT232RL, USB to serial UART interface, FTDI, SSOP-28
IC3 = ATmega168PA-PU, PDIP-28, programmed, Elektor # 100126-41)
IC4, IC5 = LM386N-1, DIL-8
Y1 = Si4735 broadcast AM/FM/SW/LW radio receiver carrier board, DIL-20, Elektor # 090740-71
Miscellaneous
ENC1 = Rotary encoder, vertical, 12 ppr, ALPS type EC12E1220401 (Farnell # 1520809)
JP1 = 3-way pinheader, 2.54 mm lead pitch + jumper
JP2-JP5 = 2-way pinheader, 2.54 mm lead pitch + jumper
K1-K3 = 2-way, screw-type terminal block, 5mm lead pitch
K4 = BNC connector 50 ohms, black, PCB, mount, Tyco Electronics type 1-1634612-0 (right angle);
type 1-1634505-0 (vertical) (Farnell # 1020957; # 1020960)
K5 = 3-way PCB terminal block, 5mm lead pitch
K6 = jack socket, 3.5mm, stereo (Farnell # 1267400)
K7 = USB socket type B, PCB mount
K8 = 6-way (2x3) header, wire-to-board (Farnell # 1096984)
LCD1 = Alphanumeric LCD 2x16, (Electronic Assembly type EA DOGM162W-A) + LED blue backlight (type EA LED55X31-B)
S1 = slide switch, SPDT, C&K type OS102011MS2QN1 (Farnell # 1201430)
S2-S5 = Tactile switch, SPNO, MULTIMEC type 3FTL6 (Farnell # 1132885) + elevation caps
X1 = 8MHz quartz crystal, low-profile, case type HC49
X2 = 32.768 kHz quartz crystal, cylindrical case (3x8 mm)
2 pcs IC socket, DIL-8
1 pc IC socket, DIL-28 narrow body
Sockets for LCD elevation
PCB, bare, Elektor # 100126-1
PCB ready assembled and tested, Elektor # 100126-91
Elektor koopt zelf bij:
Discussie (0 opmerking(en))
Caratti 5 jaar geleden
alesales 3 maanden geleden